Mains Powered Combined Heat and Carbon Monoxide Alarm with Lithium Back-up - Ei3028

The tables below show all the products that can interlink with the Ei3028.

More products may be compatible when installed in conjunction with the Ei3000MRF SmartLINK module. Please see the Ei3028RF bundle for further information.

Smoke and Heat Alarms

Carbon Monoxide Alarms

Ancillary Products

Wiring Explained

Mains powered Ei Electronics smoke and heat alarms require a 230V AC power supply and up to 12 alarms can be hardwire interlinked in one system.

To obtain a mains power supply, each alarm can be connected to the nearest lighting circuit using 2 core and earth cable with a separate, dedicated interlink cable connecting all alarms. However, if possible it is recommended that the alarms are all powered from a dedicated circuit from the distribution board using 3 core and earth cable for safety during maintenance, as the interlink cable will carry power from live alarms on other power circuits. Please see the diagram below:-

Technical Data

This is the technical data for the Mains Powered Combined Heat and Carbon Monoxide Alarm with Lithium Back-up - Ei3028.

Product Datasheets

The following datasheets are available for this product.

• Ei3028_Datasheet
• Ei3028_Instructions

Q. Where should I install carbon monoxide detectors?

A. CO detectors should be installed near boilers and other potential sources of carbon monoxide. Keep a 1 to 3 meter distance to the boiler etc to avoid small start-up CO discharges to cause false alarms.

As you are likely to be most affected by CO in areas of your home that you spend the most time in it is advisable to install detectors in those areas as well, such as the living room and bedrooms.

It is also worth noting that while one detector is better than no detectors at all, larger homes may require several detectors to cover the property fully.

Which areas to avoid?

Do not install CO alarms above or below windows.



Although most kitchens contain fuel burning appliances it is not recommended to install your detector there. Kitchens can be quite steamy while you are cooking and this may affect the sensor in the CO detector. Similarly it is not recommended to install detectors in dusty areas such as workshops or garages.

For more information please watch our video guide

Q. How do I safely dispose of my old smoke alarms?

A. Safelincs is signed up to Valpak's WEEE (Waste Electrical and Electronic Equipment) Distributor Take-Back Scheme (Registration ID: 7370). Private households can therefore drop off their electronic and electrical fire safety waste at their municipal recycling centre when they are purchasing new products from us. To find your nearest recycling centre, please visit www.recycle-more.co.uk.

Q. Can the mains powered smoke alarm range be connected to mains power via the lighting circuit?

A. Yes, hard-wired mains powered alarms can be wired to the unswitched live feed of the nearest frequently used lighting circuit.

Q. How long do the batteries last in smoke alarms?

A. The 9V alkaline batteries last 12~18 months. Lithium batteries will usually last 5x longer than their alkaline counterparts, achieving around 5 years lifetime. Some lithium cells are also rechargeable, and when used in a mains-powered alarm may last for the entire functional lifespan of the alarm. Newer alarm models may also feature a "sealed" lithium battery. These batteries are specialist components which are designed to not be removed or need replacing by the user, and have been tested by the alarm manufacturer to ensure they last for the lifetime of the alarm.

Please Note: the actual lifetime of your batteries depends on how often the alarms are tested or activated, as sounding the alarm draws more power than when the alarms are "waiting" to detect fire. You should also read your alarm's manual to make sure you only use the recommended types and brands of batteries, as failing to follow these instructions may cause the alarm to malfunction, not alerting you in the event of a fire, and might also invalidate the warranty.

Q. When the test button is pressed on an interlinking smoke alarm will this cause all the other units to go off, too?

A. Yes, by pressing the test button on one alarm all the units in that family will also be activated. To 'teach' the units which other smoke alarms belong to the same family, the smoke alarms have to be set up together during the installation. This is done by pressing a 'housecoding button' or similar process.